70mai Hardwire Kit USB-C UP06
70mai Hardwire Kit USB-C UP06
The 70mai UP06 power supply module allows the dashcam to operate even after the engine is switched off and thus supports parking mode. Stable 5V output at 2.4A ensures continuous recording. A three-stage battery protection system (11.8 V / 12.1 V / 12.4 V for 12V and 23.6 V / 24.0 V / 24.4 V for 24V) prevents over-discharge. The display shows the voltage with an accuracy of ±0.1 V. Included are "fuse tap" connectors in four standards with 5 A fuses and 3M tape.
Key features of the 70mai Hardwire Kit USB-C UP06 car accessory
- Stable output 5 V at 2.4 A
- Three-stage car battery protection
- Four types of fuse connectors (fuse tap)
- Voltage display with ± 0.1 V accuracy
- Compatible with 12-30 V installations
- Automatic shutdown after 3 minutes
- Installation without cutting cables
- Complete kit with instructions for use
Parking mode power supply
The UP06 module provides a stable 5V at 2.4A power supply, allowing the camera to record even after the motor is switched off. Function ensures that your car remains protected around the clock - whether you are inside or have left it standing for hours. Permanent parking monitoring means that any attempted break-ins, paint scratches or collisions with other vehicles will be recorded and stored in full resolution.
Protects the battery from discharge
A three-stage voltage monitoring system automatically shuts off power to the camera when the battery voltage drops below a safe level for more than 3 minutes. For 12V installations, thresholds of 11.8 V, 12.1 V or 12.4 V can be selected; 23.6 V, 24.0 V or 24.4 V for 24V systems. That way, you can be sure you'll start up in the morning without any problems - even if the camera has been recording all night.
Installation in minutes
In the package you will find fuse tap connectors in four variants - standard, MINI, low profile and MICRO2 - together with 5A fuses. Simply find a suitable fuse slot in the fuse box, connect the connector to VCC, ACC and ground, route the cable and stick the module with 3M tape. The entire installation process is cable-free and requires no special tools or service visits.
Real-time voltage control
The three-digit LED display shows the current battery voltage with ±0.1V accuracy, allowing real-time monitoring of battery status. This allows you to continuously assess the health of the electrical system and detect potential problems before they affect vehicle operation, which is especially useful before a long shutdown or in winter when the battery is most susceptible to discharge.
Compatible with every car
The module is compatible with 12-30V installations, making it suitable for most cars, vans and commercial vehicles. The Stable Power Supply System works reliably both when driving and when stationary, replacing the cigarette lighter socket and ensuring a permanent connection to the on-board network. So you don't have to worry about compatibility - if your car uses a standard battery, the UP06 will work without any problems.
Package contents:
Module 70mai UP06, 2× set of 4 adapters for fuses - standard, MINI, low profile, MICRO2 - each with 5 A fuse, 3M self-adhesive backing and instructions for use
Technical specifications
Input voltage: DC 12-30 V
Output voltage: 5V 2.4A
Three-stage low-voltage disconnect setting: 11.8V / 12.1V / 12.4V (cars with 12V installation) 23.6V/24.0V/24.4V (cars with 12V installation)
Accuracy: ±0,2V
Protection/Security: Low voltage disconnect, short circuit protection, overload protection, overvoltage protection, battery voltage monitoring
Input cable length: 1,0 m
Output cable length: 3,0 m
Termination/connector: USB-C
Mounting method: 3M adhesive pad, non-invasive set-and-forget type
Voltage display: Clear 3-digit display, ±0.1 V accuracy
Operating temperature: -20 °C to +70 °C
Specifications can be changed without notice. Images are for illustrative purposes only.
