Reviews Fractal Design Adjust Pro Hub
Interested in reviews of Fractal Design Adjust Pro Hub? It got 4.3 out of 5 stars from our customers. Find specific customer reviews of Fractal Design Adjust Pro Hub below. We will appreciate if you also share your experiences with Fractal Design Adjust Pro Hub after purchasing.
User Reviews
Vít, Olomouc 9
Rated 29/03/2026, variant Fractal Design Adjust Pro Hub
Verified purchase
This hub is very nice, compared to other cheap hubs, it allows especially the functioning of the backlight without any running SW, I consider this to be an absolutely crucial difference, e.g. SignalRGB puts such a noticeable load on the cpu that its use prevents the cpu from lowering the clock speed and the cpu consumption is then noticeably higher. The configuration itself works via the web interface, so there is no need to install anything at all. The effects setup is decent, but it doesn't have the advanced argb SW yet. But Fractal cares about customers and I wouldn't be surprised to add more setup options in the future. Of course, this hub is optimal in combination with Momentum fans, which have the necessary connector, but even older fans are not a problem to connect via the supplied reducer. Anyone who finds the package is low on cables and reducers, just email Fractal support, they sent me a whole set of cables for free, it was home within a week.
Excellent Hub with web interface that works even without running software
Solid argb setup options
Perfect for Fractal Momentum fans
Updatable firmware
Fractal support
Dear
I would like to see more detailed settings of rgb effects
0 ×Report
Automatic translation
Ondřej, Dobroslavice
Rated 06/01/2026, variant Fractal Design Adjust Pro Hub
Verified purchase
TL; DR: It's pointless, it doesn't make sense. For RGB, buy a Nollie 8 (350 CZK) or Nollie 16 (750 CZK) or another opensource box and you have a much, much better device and can use much, much better software for setup. For fan control, usually ports on the board and open source software are enough. And if not, other, small hubs will do a better and cheaper service. As a SW for ventilation then the great Fan Control, which is free, and for RGB SignalRGB, which for free does great everything most mortals need. If one had everything from FD and in that last generation (USB-C connection), I could almost understand what the purpose of this box is. These new fans can control it separately even when chained. But that's the end of it. If you want to sync a graphics card, for example, you're out of luck. A fan that is connected directly to the board? Too bad. LEDs on the board? Haha. What's not attached here, it ignores. On the other hand, if you want to synchronize the fans (and other blinkers) connected to the Hub with others in other software (e.g. SignalRGB), it is possible. But everything that is connected to the Hub is reported as one single device, with no possibility of any granular control. So by switching to WDL (the Hub can be controlled by third-party SW) this gadget for 11 hundred becomes a cable for concatenation of 4 devices, which normally costs 60 crowns. And that's the end of it. All connected fans then receive the same instruction. This is OK only if you want the whole cabinet to shine the same way. But then you don't need this device for that. I won't even go into the ventilation. Same horror, in pale blue. It can only control the channels it has inside it. Forget the graphics, forget the fans attached to the board. Forget about any complicated mixes or, heaven forbid, logic when setting the cooling. Of course, Fractal thinks the price is too low to at least give you enough cables. So you'll be looking pretty hard for cables that connect standard fans (PWM 4P and ARGB 3P) to USB-C, which only Fractal uses. Good luck. What instead? It depends on how many things you need to control. The boards themselves have enough ports to control the fan speed. The more expensive boards also have a decent number of ports for RGB control. If this number of zones is enough for you, all you need are cable extensions.
If you want to control multiple RGBs one at a time and do more complex effects, then reach for an opensource box like Nollie. You can find a list of them on the SignalRGB website. I really don't understand the point of this thing. Except Fractal will sell it to a few kids who don't care that it's useless. I'm returning this, I'm buying a Nollie 16. Case will look much better and I'll use the money I save to take the kids out for pancakes.
Fans from Fractal gen. 2 controls nicely
overpriced uselessness
for everything except a few fans in the world, it's a 4-channel hub
after rebooting, sometimes it doesn't connect at all
Compared to OpenSource alternatives, the software is very slick (both for RGB and speed control)
Few cables and extensions
ignores everything that is connected to the board, like graphics and all ARGB ports
0 ×Report
Automatic translation
Tomáš, Ostrava
Rated 31/10/2025, variant Fractal Design Adjust Pro Hub
Verified purchase
Fractal fans control perfectly
0 ×Report
Automatic translation
